Microstructure and dielectric study of pure BST and doped BSTF ceramic materials by broadband dielectric spectroscopy

Pure BST and doped BSTF (with BSTF2: Fe₂O₃ 2 wt % and BSTF4: Fe₂O₃ 4 wt %) ceramics were prepared by solid state reaction. XRD pattern showed the different phases were formed depend on the weight percent of Fe₂O₃. The crystal size and lattice parameters increased while the lattice strain decreased. The topography of the sintered samples shows increase of the grain size with increasing Fe₂O₃ ratio and hence enhances the compaction of ceramics. Broadband dielectric spectroscopy was employed to investigate the effect of magnetite nanoparticle on the dielectric properties of the pure BST ceramic. The interfacial polarization and the conductivity contribution reflect the high values of permittivity and its gradual increase as frequency decreases. The two BSTF samples show relaxation peak dynamic originated from presence of immobile species/electrons at low temperatures and defects/vacancies results from the formation of oxygen vacancies originates from the spontaneous change in oxidation states of Fe ions (Fe ^3+/Fe²⁺) at high temperatures. The relaxation rate obeys Arrhenius law at high temperatures in case of BST sample with activation energy 225 kJ/mol. This high value of activation energy at higher temperatures reflects and confirms the slowed down of the dynamics at the interphase and the decoupling nature of the OH-dynamic and the interfacial polarization.     

In-situ growth of hybrid NaTi8O13/NaTiO2 nanoribbons on layered MXene Ti3C2 as a competitive anode for high-performance sodium-ion batteries

In the work, we successfully explore a two-step hydrothermal method for scalable synthesis of the hybrid sodium titanate (NaTi₈O₁₃/NaTiO₂) nanoribbons well in-situ formed on the multi-layered MXene Ti₃C₂ (designed as NTO/Ti₃C₂). Benefiting from the inherent structural and componential superiorities, the resulted NTO/Ti₃C₂ composite exhibits long-duration cycling stability and superior rate behaviors when evaluated as a hybrid anode for advanced SIBs, which delivers a reversible and stable capacity of ∼82 mAh/g even after 1900 cycles at 2000 mA/g for SIBs.     

Physical properties of titanates,semiconductors and nickelates derived from ionization energy theory

Ionization energy theory is exploited to predict the changes to atomic polarizability for both anions and cations, the polarization in doped titanates and the energy gap in III–V and II–VI semiconductors. We then extend the above analysis to discuss the physics of metallic and superconducting phases in the recently discovered superconducting nickelates. In doing so, we are able to prove the existence of Ni²⁺ cations and oxygen vacancy in the metallic normal state of nickelates. We find that the normal state resistivity of the nickelates follows exactly as predicted by the ionization energy theory. Quantitative estimates are also given for the concentrations of Ni²⁺ and oxygen vacancy in superconducting nickelates.     

Effect of ZnO on sintering and microwave dielectric properties of 0.5CaTiO3-0.5 (Li0.5La0.5) TiO3 ceramics

The novel calcium titanate-lithium lanthanum titanate doped with zinc oxide (0.10, 0.30, and 0.50 mol. %) ceramic samples were prepared by solid-state reaction route. The phase formation, microstructure, densification, and microwave dielectric properties were investigated. It was found that the doping with zinc oxide led to a decrease in sintering temperature by 25 ^oC as compared with pure calcium titanate lithium lanthanum titanate due to the liquid phase effect. Also, the calcium titanate lithium lanthanum titanate (10ZCTLLT&30ZCTLLT)) doped with lower zinc oxide (0.10 and 0.30 mol. %) led to higher densification parameter. This was followed by increasing the zinc oxide doping up to (0.50 mol. %) which resulted in a decrease in densification and microwave dielectric properties which may be attributed to increase in porosity and grain growth upon the evaporation of zinc and oxygen vacancy. This led to the increase in dielectric loss (≈10 × 10^?4) value with 50ZCTLLT. Hence, the best result of microwave dielectric characteristics was obtained for 0.5CaTiO₃–0.5(Li_0.5La_0.5)TiO₃ with (0.10 and 0.30 mol. % ZnO) 10ZCTLLT and 30ZCTLLT ceramic samples sintered at 1175 ^oC/2h, with low dielectric constant (ε_r) = 4.4–10.5, very low dielectric loss = 1.07-2.23 × 10^?4 and high quality factor (Q x ?) ≈59-55 × 10⁴ at 8 GHz. Consequently, they can be used not only in wireless satellite communications technology but also can be used in the fifth-generation telecommunication 5G technology construction.     

Application of BaTiO3-based catalysts for piezocatalytic,photocatalytic and piezo-photocatalytic degradation of organic pollutants and bacterial disinfection in wastewater: A comprehensive review

The coupling of piezocatalysis and photocatalysis known as piezo-photocatalysis has attracted a lot of attention as one of the most effective advanced oxidation process (AOPs) for wastewater treatment, especially for the degradation of organic pollutants and disinfection of microbes. To advance this technology, there’s a need to develop lead free piezoelectric materials to drive both piezocatalytic and photocatalytic process to prevent secondary pollution due to lead toxicity. Hence, barium titanate (BaTiO₃) has been widely used as lead free piezoelectric material for several applications including water splitting, bacterial disinfection, and wastewater treatment due to its exceptional optical and piezoelectric properties. This work presents a comprehensive review on the application of BaTiO₃ as a promising lead-free piezo-photocatalyst for the catalytic degradation of organic pollutants and bacterial disinfection from aqueous solution. This review article details the optical and piezoelectric properties, modification strategies, and synthetic methods of BaTiO₃. Furthermore, the application of BaTiO₃ as a preferred piezo-photocatalyst for wastewater treatment and a future perspective is presented.     

NZFO-PZT磁电复合纳米纤维的制备及其吸波性能

采用静电纺丝法制备(1-x)Ni_0.5Zn_0.5Fe₂O₄-(x)Pb(Zr_0.52Ti_0.48)O₃(简称为(1-x)NZFO-(x)PZT, x=0.1、0.2、0.3、0.4、0.5)磁电复合纳米纤维, 研究了PZT含量对复合纳米纤维结构、电磁特性及微波吸收性能的影响。所有样品均由尖晶石结构NZFO和钙钛矿结构PZT两相所组成。由于NZFO磁损耗与PZT介电损耗的协同效应及界面效应的加强, 适量PZT相的引入可改善复合纳米纤维吸波涂层的电磁阻抗匹配和衰减特性, 提高微波吸收性能。x=0.3和0.4的复合纳米纤维分别在低频和高频范围表现出最强的微波吸收能力。当涂层厚度为2.5~5.0 mm时, x=0.3样品的最小反射损耗在6.1 GHz处达-77.2 dB, 反射损耗小于-10 dB的有效吸收带宽为11.2 GHz(2.8~12.9和16.9~18 GHz);x=0.4样品的最小反射损耗位于18 GHz处为-37.6 dB, 有效吸收带宽达到12.5 GHz(3.3~12.5和14.7~18 GHz)。     

Effect of carbon nanotubes addition on electrochemical performance and thermal stability of Li4Ti5O12 anode in commercial LiMn2O4/Li4Ti5O12 full-cell

Li₄Ti₅O₁₂ (LTO)/carbon nanotubes (CNTs) composite material is synthesized based on a solid-state method by sand-milling, spray-drying and calcining at 850 ℃ under N₂ flow. The LTO/CNTs samples with 1 wt% and 3 wt% weight ratio of CNTs addition and the pristine LTO sample are prepared. The rate performance and the thermal stability of these samples are investigated based on LiMn₂O₄ (LMO)/LTO full-cell. The results show that theweight ratio of CNTs addition has distinct effect on LTO performances. The composite materials of LTO composited CNTs have better performance at high-rate due to the intercalation enhancement by conductive network of CNTs. At second, the overcharging temperature response of the cell's surface with 1 wt% CNTs addition is the lowest. The particle size distribution is measured and the most uniform particles are obtained with 1 wt% CNTs addition. This trend could explain that the mediumquantity of CNTs is optimal to improve the heat and mass transfer and prevent the problems of crystallite growing interference and aggregation during the calcination process.     

Barium Titanate-reinforced Acrylonitrile-Butadiene Rubber: Synergy Effect of Carbon-based Secondary Filler

Acrylonitrile rubber(NBR) composites filled with barium titanate(BT) were prepared using an internal mixer and a two-roll mill. Also, a secondary filler, namely carbon nanotubes(CNT), was added in order to find a potential synergistic blend ratio of BT and CNT. The cure characteristics, tensile and dielectric properties(dielectric constant and dielectric loss) of the composites were determined. It was found that NBR/BT composites with CNT secondary filler, at a proper BT:CNT ratio, exhibited shorter scorch time(t_(s1)) and cure time(t_(c90)) together with superior tensile properties and reinforcement efficiency, relative to the one with only the primary filler. In addition, the NBR/BT-CNT composite with 80 phr BT and 1-2 phr CNT had dielectric constant of 100-500, dielectric loss of 12-100 and electrical conductivity below 10~(-4) S/m together with high thermal stability. Thus, with a proper BT:CNT mix and filler loading, we can produce mechanically superior rubber composites that are easy to process and low-cost, for flexible dielectric materials application.     

A sonochemical synthesis of SrTiO3 supported N-doped graphene oxide as a highly efficient electrocatalyst for electrochemical reduction of a chemotherapeutic drug

A sonochemical based green synthesis method playa powerful role in nanomaterials and composite development. In this work, we developed a perovskite type of strontium titanate via sonochemical process. SrTiO₃ particles were incorporated with nitrogen doped graphene oxide through simple ultrasonic irradiation method. The SrTiO₃/NGO was characterized by various analytical methods. The nanocomposite of SrTiO₃/NGO was modified with laser-induced graphene electrode (LIGE). The SrTiO₃/NGO/LIGE was applied for electrochemical sensor towards chemotherapeutic drug detection (nilutamide). Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques have been used to examine the electrochemical performance of nilutamide (anti-cancer drug). DPV was found to be more sensitive and found to exhibit a sensitivity 8.627 µA µM⁻¹ cm⁻² for SrTiO₃/NGO/LIGE with a wide linear range (0.02–892 µM) and low Limit of detection (LOD: 1.16 µM). SrTiO₃/NGO/LIGE has been examined for the detection of nilutamide in blood serum and urine samples and obtained a good recovery in the range of 97.2–99.72 %. The enhanced stability and selectivity and practical application results indicates the suitability of SrTiO₃/NGO/LIGE towards the detection of nilutamide drug in pharmaceutical industries.     

Effect of B-site isovalent doping on electrical and ferroelectric properties of lead free bismuth titanate ceramics

In the present work, zirconium modified bismuth titanate ceramics have been studied as potential lead-free ferroelectric materials over a broad temperature range (RT – 800 °C). Polycrystalline samples of Bi₄Ti_3−xZr_xO₁₂ (x=0.2, 0.4, 0.6) (BZrT) with high electrical resistivity were prepared using the solution combustion technique. The effect of Zr doping on the crystalline structure, ferroelectric properties and electrical conduction characteristics of BZrT ceramics were explored. Addition of zirconium to bismuth titanate enhances its dielectric constant and reduces the loss factor as it introduces orthorhombic distortion in bismuth titanate lattice which is exhibited by the growth along (0010) lattice plane. Activation energy due to relaxation is found to be greater than that due to conduction thus confirming that electrical conduction in these ceramics is not due to relaxation of dipoles. Remanent polarization of the doped samples increases as the Zirconium content increases.